Your heat pump installation specialists in Graham, TX. Free assessments, certified technicians, and guaranteed results.
Homeowners in Graham, Texas upgrading to a modern heat pump gain dual-mode heating and cooling from a single system, and KIC Refrigeration ensures every installation is sized, configured, and commissioned to manufacturer standards. We evaluate your existing ductwork, electrical panel capacity, and insulation levels to recommend the right unit for your climate zone and structure.
Graham homeowners and businesses count on reliable heat pump installation to maintain comfort and protect indoor air quality. Serving a city of 8,930 across Texas, KIC Refrigeration brings the experience and crew depth to handle heat pump installation projects of any scale. We begin every job with an honest evaluation and a clear, written estimate.
Our heat pump installation technicians in Graham, TX are NATE-certified, EPA 608 licensed, and equipped with advanced diagnostic tools. From the initial inspection through final commissioning, we maintain open communication and hold ourselves to the highest standards. That is how KIC Refrigeration has earned the trust of homeowners across Texas.
A clear, step-by-step approach to every heat pump installation project we take on.
We perform a Manual J load calculation on your home to determine the correct heat pump size in BTU capacity and tonnage. Oversizing causes short cycling and humidity problems. Undersizing leaves you uncomfortable on extreme days.
KIC Refrigeration provides Graham, TX homeowners with detailed equipment proposals that include model specifications, AHRI-certified efficiency ratings, estimated annual operating costs, available rebates and tax credits, and a complete installation scope of work with no hidden costs.
At your Graham property, our installation team sets the outdoor unit on a level pad, mounts the air handler, runs and insulates new copper linesets, installs the condensate drain with a proper trap, wires the disconnect and thermostat, and commissions the system to factory specifications.
We run the system through heating and cooling modes, verify pressures, airflow, and temperatures match specifications, program the thermostat, and walk you through daily operation, filter maintenance, and warranty registration.
Common questions about heat pump installation costs, timelines, and what to expect.
Heat pump installation in Graham typically costs $5,000 to $12,000 for a standard split system including the outdoor condenser, indoor air handler or coil, new thermostat, refrigerant lineset, and all labor. High-efficiency variable-speed systems from Carrier, Trane, or Daikin with SEER2 ratings of 18 to 22 range from $10,000 to $18,000 installed. Ductless mini-split systems run $3,000 to $8,000 depending on the number of indoor zones. The total price depends on home size, system tonnage, efficiency tier, ductwork condition, and whether electrical upgrades are needed. KIC Refrigeration provides detailed proposals for Graham homeowners with all costs itemized and no hidden fees.
Yes. A heat pump provides both heating and cooling from a single outdoor unit by reversing the refrigerant cycle between seasons. Modern cold-climate heat pumps with variable-speed inverter compressors operate efficiently down to 0 to minus 15 degrees Fahrenheit. In extremely cold TX climates, a dual-fuel configuration pairs the heat pump with a gas furnace that engages as backup only below the economic balance point — the temperature where gas heating costs less per BTU than electric heat pump operation. This gives you heat pump efficiency for 80 to 90 percent of the season with gas backup for the coldest days. KIC Refrigeration designs the right configuration for your Graham climate zone and heating needs.
A properly installed and maintained heat pump in Graham typically lasts 12 to 18 years before requiring replacement. Variable-speed systems with inverter compressors often last on the higher end of that range because they run at lower speeds most of the time, reducing mechanical stress and component wear. The single biggest factor in heat pump longevity is proper installation — correct refrigerant charge, proper airflow, and tight electrical connections — followed by annual professional maintenance. KIC Refrigeration offers annual maintenance plans for Graham customers that include coil cleaning, refrigerant pressure verification, electrical connection tightening, and capacitor testing to maximize your equipment lifespan.
A standard heat pump replacement in Graham where the existing ductwork and electrical service are adequate takes 1 full day — typically 6 to 10 hours from start to commissioning. New installations that require ductwork modifications, electrical panel upgrades, new concrete pads, or multiple zone setups may take 2 to 3 days. Mini-split installations with 2 to 4 indoor heads typically take 1 to 2 days. KIC Refrigeration provides a detailed timeline in your proposal, schedules the installation at a time that works for you, and keeps you informed on progress throughout the project at your Graham property.
Real feedback from customers across the country about the quality of our work.
"KIC Refrigeration cleaned our dryer vent and also noticed our exhaust duct was damaged. Fixed both on the same visit. That kind of attention to detail matters."
"KIC Refrigeration repaired our heat pump when two other companies said it needed full replacement. Saved us thousands. Still running great six months later."
"Boiler repair took a couple visits because they needed to order a part, but they were upfront about it and the repair has held up perfectly."